Home Page
   Articles
       links
About Us    
Traders        
Recipes            
Latest Articles
Cider press
Page Previous  1, 2
 
Post new topic   Reply to topic    Downsizer Forum Index -> Authors Corner
Author 
 Message
Treacodactyl
Downsizer Moderator


Joined: 28 Oct 2004
Posts: 25795
Location: Jumping on the bandwagon of opportunism
PostPosted: Tue Jan 03, 06 12:23 pm    Post subject: Reply with quote
    

It's good to get the article up now as it gives people time to make one before this Autumn! I may have to wait a little longer as I don't think we have that much room. It would look great in the kitchen though.

Jonnyboy



Joined: 29 Oct 2004
Posts: 23956
Location: under some rain.
PostPosted: Tue Jan 03, 06 12:39 pm    Post subject: Reply with quote
    

It looks like a great piece of kit, I've seen similar stuff for sale for several hundred pounds.

We made our cider with a juice extrator last year, it was slow and far from satisfactory, hopefully if I get this built we can make the most of our glut.

Jb



Joined: 08 Jun 2005
Posts: 7761
Location: 91� N
PostPosted: Tue Jan 03, 06 12:54 pm    Post subject: Reply with quote
    

Apart from scaling that down a bit what changes would one need to make to use the same design as a cheese press?

Blacksmith



Joined: 25 Jan 2005
Posts: 5025
Location: Berkshire
PostPosted: Wed Jan 04, 06 12:09 am    Post subject: Reply with quote
    

Cheese press, another use ! not sure on modifications, will make enquires.
I have made a couple of similar assemblies (minus basket) as book binding presses. The list continues...........
Dave

kinkycat



Joined: 20 Jun 2005
Posts: 62
Location: Somerset
PostPosted: Wed Jan 04, 06 7:44 pm    Post subject: Reply with quote
    

Great article. We have looked at the Vigo presses, but for a large-ish press they are asking big money.

Are you planning to make and sell presses? How much juice would you expect from a barrel squeeze? (to avoid any technical terms).

Bugs



Joined: 28 Oct 2004
Posts: 10744

PostPosted: Wed Jan 04, 06 9:51 pm    Post subject: Reply with quote
    

It seemed sensible to put this in here as there's already a discussion afoot about it, but for anyone who comes along later, here is Blacksmith's excellent guide to making a cider press from a few straightforward parts

Might be worth rehoming this thread in the R, P, Homebrewing forum?

Blacksmith



Joined: 25 Jan 2005
Posts: 5025
Location: Berkshire
PostPosted: Thu Jan 05, 06 11:47 am    Post subject: Reply with quote
    

I'm not planning on making presses, and with the downsizer ethic of "buying locally" I hope any small engineering companies will be able to make the parts not available "off the shelf". ( I can supply working drawings if you want them)
I used about 2 carrier bags (oh the shame !) of windfall apples and 1 bag of cooking apples from the market. These were mashed up using a baulk of timber, wrapped in an old net curtain and pressed.
It took 3 goes to get a gallon of juice.
Cheers, Dave.

dougal



Joined: 15 Jan 2005
Posts: 7184
Location: South Kent
PostPosted: Thu Jan 05, 06 12:22 pm    Post subject: Reply with quote
    

JB wrote:
Apart from scaling that down a bit what changes would one need to make to use the same design as a cheese press?

IMHO its overkill for cheese.

Cheese only requires a very low *pressure* (I estimate 2 to 5 psi - tiny compared to that needed for juicing), although most recipes do talk only about the *force* applied (and one has to dig around to discover the area that the force is being applied to).
The idea is that this pressure 'binds' the curds, as the whey is (gently) expelled, and the curds shrink.
The pressure has to be maintained for many hours (often 24).
With a pure screw press, designed to minimise elasticity, once the curd shrinks, the pressure will disappear.
And there's no way of gaugeing the pressure.

Hence screw-based cheese presses have a spring arrangement
1 - to measure the force by the spring's compression, and
2 - to deliberately provide elasticity, maintaining pressure on the cheese as it shrinks

And I think 'design-for-sterilisation' is more important with cheese than fruit juice (which may be pasteurised or subject to masses of the 'right' yeasts).

Blacksmith



Joined: 25 Jan 2005
Posts: 5025
Location: Berkshire
PostPosted: Sat Jan 07, 06 9:43 pm    Post subject: Reply with quote
    

If anyone is unable to source the additional parts required for the press, I am able to supply the following :
Top plate . 6mm BDMS. Drilled, tapped, finished in Hammerite paint, supplied with Hx Hd machine screws and washers to attach top nut to frame £7.50 + P & P.

Pressure plate. 6mm BDMS. Drilled. MIG welded guide tube (to suit screw) finished in Hammerite paint. £ 9.00 + P & P.

Basket Hoops. 4mm Black. MIG welded. drilled and countersunk. Finished in Hammerite paint. £ 7.50 ea ( 3 for £ 20.00) + P & P.
Dave

Post new topic   Reply to topic    Downsizer Forum Index -> Authors Corner All times are GMT
Page Previous  1, 2
Page 2 of 2
View Latest Posts View Latest Posts

 

Archive
Powered by php-BB © 2001, 2005 php-BB Group
Style by marsjupiter.com, released under GNU (GNU/GPL) license.
Copyright © 2004 marsjupiter.com